Re: Xbox 360 Arcade Stick Project
Did some more work on the pad today; this time the Play and Charge holder.
Before:
http://s3.tinypic.com/2vlv38y.jpg
After:
http://s3.tinypic.com/qz0xfn.jpg
The three screw holes that you can see in the bottom picture (reduced from 7) will be used to hold the board in place, inside the case.
Re: Xbox 360 Arcade Stick Project
Ordered some more bits and pieces today:
Quick disconnects from Lizard Lick
Sanwa JLF stick from Gremlin
NAUSB connectors from Farnell to take care of charging
Hopefully these should arrive in the next couple of days!
Re: Xbox 360 Arcade Stick Project
Quote:
Originally Posted by
Steve B
The top is split into two layers:
1 - The surface layer, made from 2mm acrylic provides a protective cover for the art inlay.
2 - The support layer, made from 6mm MDF provides a place to anchor the buttons and the joystick.
The first box I make will be like this. The second box I make, I plan on making it out of a single piece of wood, like in an electric guitar.
That's what I did with my cab, although I accidently managed to split my Area 51 marquee trying to clean it with a damp cloth :( so I bought a couple of H R Giger posters and made a new marquee and art inlay for the control panel plus some lime green Sanwa sticks, black and lime buttons plus the T-Molding to match, still not finished though.
Re: Xbox 360 Arcade Stick Project
Quote:
Originally Posted by
Zap
That's what I did with my cab, although I accidently managed to split my Area 51 marquee trying to clean it with a damp cloth :( so I bought a couple of H R Giger posters and made a new marquee and art inlay for the control panel plus some lime green Sanwa sticks, black and lime buttons plus the T-Molding to match, still not finished though.
Awesome! How far through are you?
Re: Xbox 360 Arcade Stick Project
It was a complete Area 51 cab but I've had a change of heart so I've started converting it to run Mame, I was going to keep the Area 51 artwork but after breaking the marquee I figured there wasn't much point.
Last thing I did was cut about 10cm off the bottom of the cab to make it shorter (it's a behemoth), I also need to get hold of some speakers to hide where the cables from the Area 51 guns used to go, the whole cab needs some paint, control panel needs some T-molding and I could do with respraying my coin mech.
Still quite far from finished, I'm just really really lazy.. :p
Re: Xbox 360 Arcade Stick Project
NAUSBs have arrived :)
http://i44.tinypic.com/2uoo2gx.jpg
They'll all need to be reversed though!
Re: Xbox 360 Arcade Stick Project
After a long period of absence, I've finally found some time to work on the arcade stick again. Hooray!
I've started epoxying the box together, pics to follow.
I've started preparing a second pad, which will use thicker gauge wire. My second Sanwa JLF arrived from Gremlin (finally!) along with some quick-disconnects from Lizard Lick. Again, pics to follow.
Re: Xbox 360 Arcade Stick Project
The Box
http://i40.tinypic.com/8w04yp.jpg
It went together pretty nicely. Ideally, i'd like to have some proper bar clamps, but I'm having to make do with a solitary G-clamp. :( A trip to B&Q is definitely in order!
I've set up the pillar drill with the 30mm spade bit in preparation for the Guide button going in on the front panel (that's why it's not glued completely) but it's getting quite late for doing any drilling in my top floor flat :D Spade bits are LOUD!
Router arrives tomorrow as well, so quite excited :D
Re: Xbox 360 Arcade Stick Project
Some more work done on the box today, a couple of holes drilled, router bits getting delivered tomorrow, so more progress then.
The Box
http://i40.tinypic.com/ok5479.jpg
A new pad!
http://i44.tinypic.com/2ccpcex.jpg
Re: Xbox 360 Arcade Stick Project
Got the rabbeting bit for my router today, so did a trial run on the Guide, Start and Select buttons. Also got my tiny screws for the NAUSB connector.
The Box
http://i43.tinypic.com/30ms5qx.jpg
Re: Xbox 360 Arcade Stick Project
oh, and the box that the router bit and screws came in:
http://i39.tinypic.com/261mglk.jpg
slight over-use of packaging perhaps?
Re: Xbox 360 Arcade Stick Project
Add it to the thread of shame!
Packaging Fail
Stick is looking good so far!
Re: Xbox 360 Arcade Stick Project
Looking forward to seeing how this turns out.
Re: Xbox 360 Arcade Stick Project
Got the new pad soldered up, but it's all packed up ready to be taken home, so will post pics later.
It also needs to be hot glued, as some of the contacts are incredibly small and delicate.
Re: Xbox 360 Arcade Stick Project
As promised, some pics of the new pad. Unfortunately, a few of my smaller connections broke off on the way home :( The pads are fine, but I'll be taking the epoxy to work with me tomorrow so I can apply straight after I solder them up!
Got my stand-offs sorted out. These'll be recessed into the MDF top on the underside. Battery pack is in also, so she's all coming together.
The Pad - Top Side
http://i41.tinypic.com/6scb3l.jpg
The Pad - Under Side
http://i43.tinypic.com/w8lxuc.jpg
Re: Xbox 360 Arcade Stick Project
Been doing some work on the MDF shelf that will support the buttons and the pad, amongst other things.
I kinda raped the joystick bit, which is unfortunate. This MDF shelf will probably be used until I get my acrylic, then I'll cut the acrylic at the same time as another MDF shelf.
Shelf - Top Side
http://i41.tinypic.com/1zvr61l.jpg
Shelf - Under Side
http://i41.tinypic.com/2e16jwp.jpg
Shelf - Stick Area
http://i42.tinypic.com/282g8s4.jpg