Memory Compatibilty with Intel Board DP35DP

Hi there,


I have a query about memory compatibility.

The corsair site doesn't list the motherboard for the memory I was going for. Could I check if the memory modules listed below will run well in the following Intel borad??

Also is there a noticeable differnce in performance between the two?

Motherboard - DP35DP
Spec:
1.8 V (only) DDR2 SDRAM DIMMs with gold-plated contacts
Unbuffered, single-sided or double-sided DIMMs with the following restriction: Double-sided DIMMs with x16 organization are not supported.
8 GB maximum total system memory using DDR2 667 or DDR2 533 DIMMs; 4 GB maximum total system memory using DDR2 800 DIMMs
Minimum total system memory: 512 MB
Non-ECC DIMMs
Serial Presence Detect
DDR2 800 or DDR2 667 MHz SDRAM DIMMs
DDR2 667 SIMMs with SPD timings of only 5-5-5 (tCL-tRCD-tRP)
DDR2 800 SIMMs with SPD timings of only 5-5-5 or 6-6-6 (tCL-tRCD-tRP)


Modules (option 1)
LN14277
2GB (2x1GB) CorsairTwinX XMS2, DDR2 PC2-6400 (800), 240 Pins, Non-ECC Unbuffered, CAS 4-4-4-12, EPP

(option 2)
LN11596
2GB (2x1GB) CorsairTwinX XMS2, DDR2 PC2-6400 (800), 240 Pins, Non-ECC Unbuffered, CAS 5-5-5-12

Many Thanks
Joe

Since you cannot adjust the memory voltage on that MOBO:

Quote:

---

Motherboard - DP35DP
Spec:
1.8 V (only) DDR2 SDRAM DIMMs with gold-plated contacts

---

You will need to use our Value Select memory which runs at 1.8v and at JEDEC timings.

I would recommend a PC5300 that suits your needs for the amount: http://www.corsairmemory.com/products/value_select.aspx

OK thanks

I have a related question, I found this thread while googling...
I have a DP35DP board as well, and I'm using 2 DIMMs of Corsair VS DDR2-533. Now, Intel doesn't list the board as supporting DDR2-533 memory, even though it's working fine for me. I want to add an additional 2 DIMMs that are the same kind as my current ones, and I want to be sure that the board will support 4GB (4x1GB DIMMs) of DDR2-533 before I order the memory. Does anyone know if it will work?

It should but, you should check with Intel to be sure.

Quote:

---

Originally Posted by Yellowbeard

It should but, you should check with Intel to be sure.

---

well, the problem is that intel claims the board won't work with my current 2gb of ddr2-533, but it does

My guess is that it will work if you have a 1066CPU but it won't with a 1333 as there will be no downclock option for the memory in the bios. You are welcome to try it but if there is any doubt, I would go with Intel's recommendation.

Quote:

---

Originally Posted by Yellowbeard

My guess is that it will work if you have a 1066CPU but it won't with a 1333 as there will be no downclock option for the memory in the bios. You are welcome to try it but if there is any doubt, I would go with Intel's recommendation.

---

i DO have a 1066 cpu, and i bet you're right

Hi,
I have a computer with the DP35DP and my (2x2gb) OCZ (OCZ Technology OCZ2V6672G 2GB 667MHz DDR2 PC2-5400) memory.
When I put them on the motherboard, it reads ...
But when I call, the slow the graphics in cumputador and teh computer too ... But when I put only 2gb of memory, is not that slow ...
Do you know why this problem?

Quote:

---

Originally Posted by koltipelto

Hi,
I have a computer with the DP35DP and my (2x2gb) OCZ (OCZ Technology OCZ2V6672G 2GB 667MHz DDR2 PC2-5400) memory.
When I put them on the motherboard, it reads ...
But when I call, the slow the graphics in cumputador and teh computer too ... But when I put only 2gb of memory, is not that slow ...
Do you know why this problem?

---

This section if for support of Corsair memory and not OCZ. Please contact OCZ for assistance with their products.