What are your settings for overclocks?
fsb, multiplier, v core and memory settings.
I have mine at 2.4 but i was hoping for a little more, just wondering what everyones using :)
Printable View
What are your settings for overclocks?
fsb, multiplier, v core and memory settings.
I have mine at 2.4 but i was hoping for a little more, just wondering what everyones using :)
1.9v @ 2600mhz 13 x 200, but I am sure the has to be a thread somewhere with loads of these, btw you might want to update your sig :)
Once i get replacements for my Hyperx it will be in the region of 220*11 at about 1.9V
Will attempt to get the FSB as high as is humanly possible though:)
My new 1500xpm is going in later.... ordered sunday night about midnight, arrived 9am this morning from cpucity. Hopefully I'll be able to hit something like you 2500xpm guys. Any hints for this cheaper chip?
Reports say they will all hit 2.4 pretty easily. Not bad considering its over 1000MHz overclock from stock :)
Well my ram was cheap so not much fsb overclock for me ( maxes out at 210 at the mo) but i can get my 2500-m to 2.5 on only 1.675v it was one of the 0402's. Running an slk-800a and a zalman 92mm fan + bracket. Temps in mid forties but im not running any case fans at the moment cos for some reason they all broke (?) When i get 3 120mm vantec stealths going then i'll try getting higher.
What are your volts/temps/casefans steve?
200x12 2.4 GHz 1.6v core
Ram is on aggressive- dont know much at all about memory im afraid.
Im running an slk800 with a papst fan
Cpu temp is 60 idle and the system is 32
This is in a blackwidow w/4 case fans- 3 of those may aswell not be the there because of the useless fangrills on the blackwidow that block everything :(
When i try to go above 2.4 it doesnt like it... wouldnt post and i couldnt put it back to 2.4 for a few hours :confused:
RAM timings shouldn't be a problem if you're not going over 200FSB. It probably needs a load more voltage but with those temps i wouldn't like to push it further. I wouldn't let it get above 60 idle cos thats getting a bit dodgy
So i need better ram or better cooling. Ah well. I'l clock it more when it gets colder
12.5 * 196 = 2450mhz
at about 1.75 ish volts
See my sig for speeds. Is on 1.65 and did go to 13x193 at same volts but then this heat came along! Was good for hours of Champ man.
11x237@1.825V
Volcano 12/AS5
2x256Mb TwinMOS PC3700 "43B" chips
DFI Infinity 11/27 BIOS
200 x 11.5 @ 1.75v is the best I can get :( , not much better than my locked XP2500+. However, I'm not complaining, its still a heck of a lot faster running most applications than my PIV system running at 3.1 ghz.
Grrr... just put my xpm1500 in my nf7s and it won't boot into windows at anything more than 1333mhz :( Should I reinstall as I was running a thunderbird 1ghz beforehand? I'm not entirely impressed - tried upping voltage to 1.8v and it won't even do 200x8 on the most relaxed memory timings I can set :(
Zathras, start a thread on this and we'll talk... don't wanna change steves thread.
Steve, you might wanna buy urself a dremmel and get rid of those grills.... can drop temps by 5C or so, and its def ur temps that arent helping ur overclock.
Had one of my RMA'd stealths turn up today, so that'll go in tomorrow and we'll see how temps go from there. It'll be going back on the side blowing over the 9700. Meant to push 50cfm so hopefully temps will drop, though still waiting for my stealth to come back from overclock. They really did all break...
Leon - directors cut rules...
I think ive got my speeds in my sig, but had to cut my testing time short because i blew my board! Not really limited by my RAM since ive got a gig of BH-5 :)