As it says up there ^^ 120mm diameter
This would be to fit on the inside of my case side but without fouling the top of my Noctua CPU cooler.
Clearance approx 21mm atm
Is there anything?
As it says up there ^^ 120mm diameter
This would be to fit on the inside of my case side but without fouling the top of my Noctua CPU cooler.
Clearance approx 21mm atm
Is there anything?
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
Gibbo,
What chassis do you have?
D'oh, read your sig... Antec TX1050 case yeah?
Edit:
The majority of the 120mm fans that I just scanned through on our site are 120x120x25...
You could always mod either the case or the fan, shave a few mm off maybe if at all poss? Not ideal but a quick search for 120x120x21 dimensions doesn't look promising ...
Last edited by leepen@scan; 28-05-2009 at 11:30 PM. Reason: sig
Lee P Retail Sales & System Quotes - leep@scan - 0871 4724786 (Direct) - Check out my mixes here;
www.mixcloud.com/penrar
I think we have a winner...
Now just have to see if we can get some...
Lee P Retail Sales & System Quotes - leep@scan - 0871 4724786 (Direct) - Check out my mixes here;
www.mixcloud.com/penrar
Gibbo (29-05-2009)
Last edited by Gibbo; 29-05-2009 at 12:19 AM.
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
Yeah but it's far from std....however atm it just has the open grill that used to feed the 92mm duct over the old style P4 diddy CPU cooler....now that I have a monster Noctua in there then I need to do something with the grill/hole but there's only 21mm clearance between the top of the copper pipes that stick out of the heatsink and the inside of the side panel....
I had thought about and still am thinking about attaching the 92mm duct to the outside of the case and blowing down the duct with a 92mm fan but who wants a 4" 'chimney' sticking out the side of their case?
Oh I dunno it'd certainly look funky...
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
oh and while we're at it I'd be in the market for some 120mm and 80mm filter style grills - mesh? foam? whatever?
Not seen such a thing at Scan.....
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
Purchasing are on the case - shall let you know when I get some more info
Lee P Retail Sales & System Quotes - leep@scan - 0871 4724786 (Direct) - Check out my mixes here;
www.mixcloud.com/penrar
Gibbo (29-05-2009)
Oh and while you're on at purchasing how about some large poly/rubber grommets or 'grommet edging' ?....I have decided to perforate my motherboard tray to improve cable management and also cut 2 holes in the rear of the case to pass the 24pin ATX cable outside the case and back in again...have you seen the ridiculous placement of the power socket on a P5QL-E?
I need the sharp edges that will result protected....
Thanks
Edit:
perhaps stuff like this:
http://www.performance-pcs.com/catal...ducts_id=21506
that performance pcs site is great
Last edited by Gibbo; 29-05-2009 at 09:54 AM.
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
I've found most of what I need at another supplier but will wait until next week until ordering as I seem to have run out of money this month!
Edit:
but no out of stock there of most of what I'm after...I'll wait and see if Scan come up with any interesting options...
Last edited by Gibbo; 29-05-2009 at 02:25 PM.
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
any news on these?
I didn't place the order elsewhere as I wasn't confident that they'd deliver - there was something funny going on with their site....
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
news?
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
Any news on the Yate Loon 120x120x20mm fans?
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
I bought a Yate Loon fan somewhere else now at a very reasonable £3.99.
Asus P5QL-E : Intel Q9550 : Noctua NH-U12P : DDR2 2 x 2048MB 1066 Corsair : Palit 9800GT 512Mb : Iiyama PLE2200WS-B : RME HDSP9632[a proper musician's card] : 2 x SATA 7200rpm 250GB : 1 x 7200rpm IDE 120GB : 1 x 7200rpm IDE 80GB : Iomega 34290 1TB eSATA storage : Pioneer DVR-216DBK : Antec TX1050 case : TAGAN TG700BZ PSU : MOTU MTPAV MIDI interface/time clock : Behringer BCR2000 : SONAR 7PE : Reason3 : ReFX Nexus : ReFX Vanguard : NI Battery3 : JP-8080 : D-50 : D-10
There are currently 1 users browsing this thread. (0 members and 1 guests)