Results 1 to 6 of 6

Thread: mdk 10 and sil 3112 SATA RAID

  1. #1
    HEXUS.social member Agent's Avatar
    Join Date
    Jul 2003
    Location
    Internet
    Posts
    19,185
    Thanks
    738
    Thanked
    1,609 times in 1,048 posts

    Unhappy mdk 10 and sil 3112 SATA RAID

    Does anyone know how to make this work properly ?

    I have 2 * 80gig, SATA, 7200rpm, 8meg cache drives on RAID 0, using the onboard sil 3112 controler.
    When setup trys to look at the drives at the "licencing" stage of setup, you can hear the drives constantly clicking, and setup will just hang. This is with one 100gig partition, and one 60gig partition, both NTFS formated.
    If i delete the 60 gig partition (which i dont need), setup will read the hard disk partitioning part of the install. At this point it looks like its seeing 2 seperate drives !. I always thought that once the SATA BIOS had kicked in, the drives would only appear as one due to it being done at hardware level, and not software ?
    The 100gig partition is also reading as somthing like 120% of the disk space usage

    Well at this point, im scared to touch anything on the drive"s" because it will probably kill the array.

    Any offers ?
    Quote Originally Posted by Saracen View Post
    And by trying to force me to like small pants, they've alienated me.

  2. #2
    Oh no!I've re-dorkalated! Jiff Lemon's Avatar
    Join Date
    Jul 2003
    Location
    Sunny MK
    Posts
    2,504
    Thanks
    80
    Thanked
    44 times in 41 posts
    you loaded the driver at the "press f6 to load additional drivers" stage?

  3. #3
    HEXUS.social member Agent's Avatar
    Join Date
    Jul 2003
    Location
    Internet
    Posts
    19,185
    Thanks
    738
    Thanked
    1,609 times in 1,048 posts
    Quote Originally Posted by Jiff Lemon
    you loaded the driver at the "press f6 to load additional drivers" stage?
    Im talking about linux here and not windows
    (unless it has that option and im totaly blind )
    Quote Originally Posted by Saracen View Post
    And by trying to force me to like small pants, they've alienated me.

  4. #4
    Comfortably Numb directhex's Avatar
    Join Date
    Jul 2003
    Location
    /dev/urandom
    Posts
    17,074
    Thanks
    228
    Thanked
    1,026 times in 677 posts
    • directhex's system
      • Motherboard:
      • Asus ROG Strix B550-I Gaming
      • CPU:
      • Ryzen 5900x
      • Memory:
      • 64GB G.Skill Trident Z RGB
      • Storage:
      • 2TB Seagate Firecuda 520
      • Graphics card(s):
      • EVGA GeForce RTX 3080 XC3 Ultra
      • PSU:
      • EVGA SuperNOVA 850W G3
      • Case:
      • NZXT H210i
      • Operating System:
      • Ubuntu 20.04, Windows 10
      • Monitor(s):
      • LG 34GN850
      • Internet:
      • FIOS
    can't remember anyting, i gave up after not one distro picked up on drives attached to my Promise 20376 controller

    however, iirc linux DOES see drives separately under RAID, as you can't (for example) boot from a RAID 1 array Windows style - you create a /boot partition on one drive, the big / partition on both drives, then use the leftover space on the other drive for swap

  5. #5
    daft ideas inc. scottyman's Avatar
    Join Date
    Jul 2003
    Location
    Charming and Exotic Bracknell
    Posts
    1,576
    Thanks
    2
    Thanked
    3 times in 3 posts
    I had no problems using the same controller.
    Which release of the driver did you use? standard version in the community edition?
    I'm not using Raid 0, instead am addressing both drives seperately, with the second 120 acting as shared storage between my xp install and mandrake. Might be worth seperately assigning /boot / and swap to see if that does the trick.
    It's entirely possible that the driver on the disc doesn't actually support raid level 0.

    Scotty

  6. #6
    daft ideas inc. scottyman's Avatar
    Join Date
    Jul 2003
    Location
    Charming and Exotic Bracknell
    Posts
    1,576
    Thanks
    2
    Thanked
    3 times in 3 posts
    actually - can you try the install in text mode - will throw the errors correctly rather than supressing them. Looks like there are a few people out there experiencing problems in SUSE 9.0 on the new kernel also.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •