Re: C2D Overclocking Guide For Beginners P5K Add-On
Quote:
Originally Posted by
TurboTronix
Since P5K premium uses DDR2 does it affect the ram settings or I should be fine with the first post settings?
Also, I haven't overclocked my system yet and I noticed the Mobo temp hits 45-50, should I add the little fans on the heatsinks that I got with my mobo?
My system info is as follows:
CPU: Q6600 G0
Mobo: Asus P5K Premium
Ram: 4GB dual shared OCZ Gold
Vid: X800XL Water cooled (soon to be upgraded to Geforce 8800 Ultra water cooled)
Cooling: Zalman Reserator 1 (water tank removed internal pump) + SWIFTECH MCW50 VGA + Zalman ZM-WB2 CPU Block + Swiftech MCR320 with 3 X 120mm quiet fans + Swiftech MCP655 pump
I'm not entirely sure what you mean.
If you are asking if you should manually set the RAM timings and voltages, then the answer is a definite YES :)
You can use the little fans that come withy the motherboard, but that isnt the area that gives you your motherboard temp.
There is a motherboard temp sensor on the P5K.
http://eservice.asus.com.tw/eService...8E15FB9F90.JPG
It is in an unfortunate place, as it gets residual heat from the CPU and mosfet areas, so blowing a fan over it, will give you more accurate temps, but its nothing to worry about.
Re: C2D Overclocking Guide For Beginners P5K Add-On
Now I got the FSB to 400 with cpu voltage at 1.4625 I believe. I had the PC run at temp of 45 avg per core.
Now after I updated my WinXP 64bit the PC boots into windows but then when I place the cursor onto the toolbar it is represented as an hourglass icon as if the PC is thinking. This longs for several minutes...I am able to move the mouse and press the CapLock (light goes ON/OFF) but I am not able to click on anything or get the Start menu to show.
Is it a software issue or ram?
It does the same thing once I bring back the settings in BIOS to default.
Re: C2D Overclocking Guide For Beginners P5K Add-On
I have p5k deluxe wifi/ap with Q6600. the problem started when I got system setup, when i push power button, no display come on screen, the HDD led is solid red, i push reset button few times, screen come on and says 'overclock failed'. i followed your guide, now it doesnt say overclock failed anymore, or at least not that frequently, but every time i turn if on, i push the power button no display, i have to push reset button, the system shutdown and turn back on, then screen come on .
here is the settings:
JumperFree Configuration Settings
AI Overclocking: Manual
CPU Ratio Control: auto
FSB strap to North Bridge: 266 MHZ
FSB Frequency: 266
PCI-E Frequency: 100
DRAM Frequency: DDR2-667
DRAM Timing Control: auto
DRAM Timing Control [manual]
CAS# Latency: 5
RAS# to CAS# Delay: 5
RAS# Precharge: 5
RAS# Activate to Precharge: 15
TWR: AUTO
TRFC: AUTO
TWTR: AUTO
TRRD: AUTO
TRTP: AUTO
DRAM Static Read Control: Disabled
Transaction Booster: Disabled
Clock Over-Charging Mode: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Voltage: Auto
CPU Voltage Reference: AUTO
CPU Voltage Damper: Enabled
CPU PLL Voltage: Auto
DRAM Voltage: 2.20
FSB Termination Voltage: Auto
North Bridge Voltage: Auto
North Bridge Voltage Reference: AUTO
South Bridge Voltage: AUTO
Advance CPU Settings
CPU Ratio Control: Auto
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
CPU TM Function: Enabled
Execute Disable Bit: Disabled
PECI: Enabled
Intel SpeedStep: Enabled
asus p5k deluxe wifi/ap
intel Quad core Q6600
ATI radeon x1600 pro
can you tell me how to fix it?
Re: C2D Overclocking Guide For Beginners P5K Add-On
Try changing this to AUTO: PCI-E Frequency: 100
Quote:
Originally Posted by
citrix
I have p5k deluxe wifi/ap with Q6600. the problem started when I got system setup, when i push power button, no display come on screen, the HDD led is solid red, i push reset button few times, screen come on and says 'overclock failed'. i followed your guide, now it doesnt say overclock failed anymore, or at least not that frequently, but every time i turn if on, i push the power button no display, i have to push reset button, the system shutdown and turn back on, then screen come on .
here is the settings:
JumperFree Configuration Settings
AI Overclocking: Manual
CPU Ratio Control: auto
FSB strap to North Bridge: 266 MHZ
FSB Frequency: 266
PCI-E Frequency: 100
DRAM Frequency: DDR2-667
DRAM Timing Control: auto
DRAM Timing Control [manual]
CAS# Latency: 5
RAS# to CAS# Delay: 5
RAS# Precharge: 5
RAS# Activate to Precharge: 15
TWR: AUTO
TRFC: AUTO
TWTR: AUTO
TRRD: AUTO
TRTP: AUTO
DRAM Static Read Control: Disabled
Transaction Booster: Disabled
Clock Over-Charging Mode: AUTO
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Voltage: Auto
CPU Voltage Reference: AUTO
CPU Voltage Damper: Enabled
CPU PLL Voltage: Auto
DRAM Voltage: 2.20
FSB Termination Voltage: Auto
North Bridge Voltage: Auto
North Bridge Voltage Reference: AUTO
South Bridge Voltage: AUTO
Advance CPU Settings
CPU Ratio Control: Auto
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
CPU TM Function: Enabled
Execute Disable Bit: Disabled
PECI: Enabled
Intel SpeedStep: Enabled
asus p5k deluxe wifi/ap
intel Quad core Q6600
ATI radeon x1600 pro
can you tell me how to fix it?
Re: C2D Overclocking Guide For Beginners P5K Add-On
Try putting some voltage on your vdimm your still at stock voltage.
Just try upping it a notch at a time until you get some stability using orthos.
luck:)
Re: C2D Overclocking Guide For Beginners P5K Add-On
ok. I just changed that.
the thing is, if i turn it off and turn on immediately, it can start. sometimes if I turn if off for 1 or 2 hours, then when i turn power on, it's like this.
Re: C2D Overclocking Guide For Beginners P5K Add-On
THe symtoms you describe are those of a failed oc as you experienced with the
Quote:
'overclock failed'
message. A failing oc can take on a variety of smptoms , of which you have your share.
As i said earlier that's to be expected running 9x400fsb at stock vcore. Given that the steps in vcore are 0.0125v you may need to increase it a good few steps before the symptoms go away. Of course increasing vcore will also impact your temps so keep an eye on them as well.
Re: C2D Overclocking Guide For Beginners P5K Add-On
i tried everything. it still wont turn on. i have to push reset button few times until in come on, and now it less frequently say 'overclock failed', or not every time it turn on. but it just wont turn on when i push power on.
anybody have the same problem?
Re: C2D Overclocking Guide For Beginners P5K Add-On
Sounds like duff RAM to me.
Take out one of the sticks and test with memtest v1.70 test 5, then try that same stick in all the slots, doing the same test, then do the same with your other stick/s.
You may find that you have one dying/dead stick of RAM.
Re: C2D Overclocking Guide For Beginners P5K Add-On
RAM is brand new, 2 sticks, showing 2GB in windows and BIOS.
Re: C2D Overclocking Guide For Beginners P5K Add-On
Re: C2D Overclocking Guide For Beginners P5K Add-On
I tried to either sticks in either slot. it still says 'overclock failed'.
Re: C2D Overclocking Guide For Beginners P5K Add-On
Do you have any other DDR2 to try?
I am assuming that you have set the voltage for the RAM manually?
Re: C2D Overclocking Guide For Beginners P5K Add-On
i have some DDR2-533, but will not fit this board. i tried before, i got black screen.
DRAM voltage is set to auto. I tried 2.20V, did not help.
Re: C2D Overclocking Guide For Beginners P5K Add-On
What RAM is it?
And have you flashed to the latest bios?
Can you put your system specs in your "my system" bit?
Re: C2D Overclocking Guide For Beginners P5K Add-On
it's VS1GB667D2 . i have bios 0404.