I think he just sanded it. Which case that means rust city in a couple months...that or its gunna be really oily...
I think he just sanded it. Which case that means rust city in a couple months...that or its gunna be really oily...
Asus A7N8X-D Rev. 2.0 / BFG FX5900U 256MB / Mushkin DDR400 BH5 2x512 / AMD XP2500+ @ 3400+
Just thought i would add these, hand etched.
He sprayed it first with a silver colour, then scratched it to give that effect I believeOriginally Posted by Whiternoise
My actual computer, 201b-SX1 case with 2x pioneer 109xlc limited edition brushed alu drives, lian li TR3, power/reset LEDs swapped out for blue ones, 2x 80mm blue Silenex LED fans in the front, Evercool Alu rear and top 80mm fans (for sexy looks) More picture in link in sig:
The family:
From left to right:
111b-SX2 - Newly restored - See link in sig
111c-SX1 - Mint in box, never used
201b-SX1 - My PC, mint condition but obviously used - See link in sig
201b-SXK - Some might say 'silver widow' excellent conditon but has been used
201c-SX1 - Mint in box, never used
201c-SX1 - Breaking up for spare parts
Just need get rid of the 111b-SX2 and the 201c-SX1 and replace with a 100, 101, 200-SX1/2 and/or a 500 to make my family complete!
Pic 1:
Pic 2:
Pic 3:
Thanks,
randomJ.
Thats the Eclipse 62 right? Nice case that. I do like cases with pre-sprayed internals. Much easier than doing it yourself.
Just spent a quick minute tidying the cables in my pc, lot better than the were originally when I built the pc, better airflow as a result too....
Only really 'modded' PC (out of the 6 that reside in my tiny little bedroom).
Biggest accomplishment was cramming it all into such a small chassis. Yes that is a full size ATX board.
Spec wise its getting on a bit now, 2GHz Mobile Barton, 512MB RAM, Golden Limited 5900XT, plugged into an Abit KV7. Still ahndles whatever I throw at it, even if it does take it a couple of hours per film.
Last edited by lost eden; 15-06-2006 at 02:54 PM.
All closed up
With the side off
from the side
http://img75.imageshack.us/img75/8581/p10100117ft.jpg
Same again, but with flash on - the fan looks like it's stopped
Close up of CPU + rear fan
http://img125.imageshack.us/img125/9601/p10100125wg.jpg
Nice little pic of it alongside the monitor with the side off
http://img125.imageshack.us/img125/3649/p10100176gg.jpg
£8 case holding:
- AMD Athlon XP 3000+ skt 754 (2.0ghz) at 2.4Ghz
- Foxconn motherboard
- Akasa Blue LED CPU cooler
- Leadtek GeForce 6200TD (OCed a bit)
- 1x200GB IDE HDD
- 1x60GB IDE HDD
- 2xLED case fans
- Magna 500w PSU (cheapo PSU, more likely 330W or something)
- 1x DVD Reader
- 1x Faulty DVD Re-Writer
- 1x FDD
- Philips 4.1 Soundcard
Someone asked about a pic when discussing watercooling:
Spec as per sidebar <--
It's an Alphacool Basic kit, 8mm ID kit hose, I want to fit a GPU block at some point. The top fan and connector housing from the case has been removed to allow the radiator to sit on the case. It's got standoffs made from Alu tube bolted into rubber chair feet from Homebase. I used a bit of secret spec foil to wrap round the pipe running behind the PSU exhaust. I want to fit an extractor fan or two, to bring down the case temp.
My first foray into watercooling, thus far a success.
looks nice m8.
PowerColor HD 4850 512MB
Gigabyte GA-EP35-DS3L iP35 Socket 775 8 channel audio ATX Motherboard
Intel Core 2 Duo E7200 2.53GHz
Coolermaster Centurion 5 All Black
Corsair 450W VX 450W PSU
Samsung SpinPoint F1 500GB
that case looks eerily familiar! don't suppose it came out the back of a white van...Originally Posted by BigFatCat
Ha! Wrong one, that one off the back of a lorry's sitting idle with my old gear inside it Makes a cool doorstop and speaker stand.Originally Posted by jamena
i dont get it :S
PowerColor HD 4850 512MB
Gigabyte GA-EP35-DS3L iP35 Socket 775 8 channel audio ATX Motherboard
Intel Core 2 Duo E7200 2.53GHz
Coolermaster Centurion 5 All Black
Corsair 450W VX 450W PSU
Samsung SpinPoint F1 500GB
Don't worry, it's just flashbacks to a dodgy second hand deal, thrashed out at a services on the M4 Completely the wrong case though, as I've even put the make and model on the image!
it looks very similar apart from the feet ... and the two 80mm instead of one 120mm rear vents... Anyway, good to hear it's useful as a doorstop
There are currently 1 users browsing this thread. (0 members and 1 guests)