ip35 crashes

[Abit_NL]

i have emailed abit from the email supplied on this site and it bounces back great support.

What mail address are you mailing to?

Regards

[csi_grissom]

This is an automatically generated Delivery Status Notification

THIS IS A WARNING MESSAGE ONLY.

YOU DO NOT NEED TO RESEND YOUR MESSAGE.

Delivery to the following recipient has been delayed:

techsupport-uk@abit.eu

Message will be retried for 2 more day(s)

Technical details of temporary failure:
TEMP_FAILURE: The recipient server did not accept our requests to connect. Learn more at Help Center - 'The recipient server did not accept our requests...'
[abit.eu (1): Connection timed out]

[Abit_NL]

This is an automatically generated Delivery Status Notification

THIS IS A WARNING MESSAGE ONLY.

YOU DO NOT NEED TO RESEND YOUR MESSAGE.

Delivery to the following recipient has been delayed:

techsupport-uk@abit.eu

Message will be retried for 2 more day(s)

Technical details of temporary failure:
TEMP_FAILURE: The recipient server did not accept our requests to connect. Learn more at Help Center - 'The recipient server did not accept our requests...'
[abit.eu (1): Connection timed out]

I don't think there is a problem with our mail server, because other mails are just coming in and I tested techsupport-uk@u-abit.eu with my personal Hotmail.

Maybe the connection with your ISP (if you are using the mail account from your ISP and not Hotmail) and our ISP is causing some problems.

If possible, give it a try with another mail account.

[Abit_NL]

Please try to set the timings a bit more relaxed to 5-5-5-18 (2.1 Volt) and increase the MCH voltage 1.35 for testing.

[csi_grissom]

used another email now see if it goes through, yes ill try them settings.

[csi_grissom]

those settings are working right now @20mins of orthos testing, but the abit eq isnt happy at the voltage of 2.1, what should we adjust now? im ready to push this further if you are m8.

[Abit_NL]

those settings are working right now @20mins of orthos testing, but the abit eq isnt happy at the voltage of 2.1, what should we adjust now? im ready to push this further if you are m8.

Please change the "warning level" from Abit EQ. You can set the high limit to 2.3 Volt.

[csi_grissom]

is that setting in abit eq?

[Abit_NL]

is that setting in abit eq?

Yes, go into the setup from the Abit EQ (the button with the screwdriver). Then press on the "limit" button that is at DDR voltage.

[csi_grissom]

ok is this the best setting for these ram now? seems mad to not be able to run them at there meant speeds...

[Abit_NL]

ok is this the best setting for these ram now? seems mad to not be able to run them at there meant speeds...

I think you should try to fine tune them now. You have some stable timings and voltages now as a basic setup. Go from there and try to change the settings step by step.

[csi_grissom]

yeah but by what im not familiar with these types of settings, how much and which one do i tweek?

[csi_grissom]

Hello???

[Abit_NL]

yeah but by what im not familiar with these types of settings, how much and which one do i tweek?

If you are not familiar with it you can try to learn it. Just learning by doing, that's the best way to get familiar with it.

For the timings the first 4 options are the most important ones:
- CAS Latency
- RAS to CAS
- RAS Precharge
- Precharge delay

And the VDIMM off course.

You need to play around with it and see what the best settings are. Nobody can tell you what the best settings are, because it is different in mostly every situation.

[csi_grissom]

but if the stock settings are 4-4-4-15 and they are not working for me and i adjusted it to 5-5-5-15 from the info on here it doesnt give me much to play with does it?