Page 3 of 3 FirstFirst 123
Results 33 to 37 of 37

Thread: Help me with my new chip!

  1. #33
    Member
    Join Date
    Jul 2003
    Location
    South
    Posts
    158
    Thanks
    1
    Thanked
    0 times in 0 posts
    Originally posted by Deckard


    Cant find a divder anywhere in the BIOS though, does this board have them locked out as mentioned earlier in this thread?
    No it's not locked, you are running your AGP/PCI out of spec, but as I said a couple of post back, thats not really a problem with modern devices

  2. #34
    No more Mr Nice Guy. Nick's Avatar
    Join Date
    Jul 2003
    Posts
    10,021
    Thanks
    11
    Thanked
    316 times in 141 posts
    Ta M@tt.

    Ok, next question, what do you reckon I should do about voltages? Leave them as they are or should I increase them a tad?

    I ask cos it just hung when I looped it thru 3D mark again, which seems odd as it was fine first time.
    Quote Originally Posted by Dareos View Post
    "OH OOOOHH oOOHHHHHHHOOHHHHHHH FILL ME WITH YOUR.... eeww not the stuff from the lab"

  3. #35
    HEXUS.timelord. Zak33's Avatar
    Join Date
    Jul 2003
    Location
    I'm a Jessie
    Posts
    35,176
    Thanks
    3,121
    Thanked
    3,173 times in 1,922 posts
    • Zak33's system
      • Storage:
      • Kingston HyperX SSD, Hitachi 1Tb
      • Graphics card(s):
      • Nvidia 1050
      • PSU:
      • Coolermaster 800w
      • Case:
      • Silverstone Fortress FT01
      • Operating System:
      • Win10
      • Internet:
      • Zen FTC uber speedy
    volts up a tiny bit

    Quote Originally Posted by Advice Trinity by Knoxville
    "The second you aren't paying attention to the tool you're using, it will take your fingers from you. It does not know sympathy." |
    "If you don't gaffer it, it will gaffer you" | "Belt and braces"

  4. #36
    HEXUS.timelord. Zak33's Avatar
    Join Date
    Jul 2003
    Location
    I'm a Jessie
    Posts
    35,176
    Thanks
    3,121
    Thanked
    3,173 times in 1,922 posts
    • Zak33's system
      • Storage:
      • Kingston HyperX SSD, Hitachi 1Tb
      • Graphics card(s):
      • Nvidia 1050
      • PSU:
      • Coolermaster 800w
      • Case:
      • Silverstone Fortress FT01
      • Operating System:
      • Win10
      • Internet:
      • Zen FTC uber speedy
    Originally posted by d_fresh1
    austin is so the man
    That is SO bang out of order I'm gonna go into a small one now

    Austin is a top top bloke and he does know way more than me...this example is a bad example of his help, and it is not his fault. Its just my experience...however the man knows SO MUCH STUFF it pains me

    Austin...please dont be offended by that lot.....you are 100% valued here

    Quote Originally Posted by Advice Trinity by Knoxville
    "The second you aren't paying attention to the tool you're using, it will take your fingers from you. It does not know sympathy." |
    "If you don't gaffer it, it will gaffer you" | "Belt and braces"

  5. #37
    Member
    Join Date
    Jul 2003
    Location
    South
    Posts
    158
    Thanks
    1
    Thanked
    0 times in 0 posts
    I would say up the Vcore a little, most JUIHB 1700's I have played with were not 24/7 stable above about 2000 Mhz at default volts and you are at 2075 now.

    Its so hard to say for sure what maybe causing your crashes without testing one thing at a time.

    eg.

    Test with a low multiplier and raise the fsb, testing as you go at your chosen Mem timings to see how far you can go.

    Next in a ideal world raise you multiplier to test for the max Mhz you can at run at stable with your chosen Max Vcore (cooling will decide you max Vcore).

    Then you can test with slack mem timings with a low multiplier to find the FSB limits of the Motherboard/something else.


    ATM I have a couple of relativly poor clocking JUIHB 1800's running @ 2200 Mhz with 1.75 Vcore

    If you look at the PIFast challenge some people have XP 1700 benchmarking @ 2500 Mhz ish with air cooling although I doubt they are 24/7 stable at that speed
    Last edited by M@tt; 11-09-2003 at 07:24 PM.

Page 3 of 3 FirstFirst 123

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •